troubles with script

[snake444]

when i run the script i get error, log :

Code:

eth1: No such device
IPv6 configuration failed!

the script's code:

Code:

#!/bin/sh
if ! [ -f /proc/net/if_inet6 ]
then echo "IPv6 is not installed!" 1>&2; exit 1; fi
ifconfig sit0 up \
&& ifconfig sit0 inet6 tunnel ::213.121.24.85 \
&& ifconfig sit1 inet6 add 2001:618:400::591:cb1f/128 \
&& route -A inet6 add ::/0 gw fe80::d579:1855 dev sit1 \
&& route -A inet6 add 2000::/3 gw fe80::d579:1855 dev sit1 \
&& ifconfig eth1 up \
&& ifconfig eth1 inet6 add 2001:618:400:b733::/64 \
&& echo 1 > /proc/sys/net/ipv6/conf/all/forwarding \
&& echo 'interface eth1
{
AdvSendAdvert on;
prefix 2001

:618:400:b733::/64
{
  AdvOnLink on;
  AdvAutonomous on;
};
};' > /etc/radvd.conf \
&& /etc/init.d/radvd start \
&& echo "IPv6 configuration completed" || \
{ echo "IPv6 configuration failed!" 1>&2; exit 1; }

 

and when i do ifconfig there is:

Code:

snake@delta:~$ ifconfig
eth0      Link encap:Ethernet  HWaddr 00:E0:4C:77:CD:1D
      inet6 addr: fe80::2e0:4cff:fe77:cd1d/64 Диапазон:Link
      UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
      RX packets:270656 errors:0 dropped:0 overruns:0 frame:0
      TX packets:250379 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:1000
      RX bytes:275446383 (262.6 MiB)  TX bytes:21518725 (20.5 MiB)
      Interrupt:20 Base address:0x2000

lo        Link encap:Local Loopback
      inet addr:127.0.0.1  Mask:255.0.0.0
      inet6 addr: ::1/128 Диапазон:Host
      UP LOOPBACK RUNNING  MTU:16436  Metric:1
      RX packets:84 errors:0 dropped:0 overruns:0 frame:0
      TX packets:84 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:0
      RX bytes:4817 (4.7 KiB)  TX bytes:4817 (4.7 KiB)

ppp0      Link encap:Point-to-Point Protocol
      inet addr:89.1.203.31  P-t-P:212.29.206.60  Mask:255.255.255.255
      UP POINTOPOINT RUNNING NOARP MULTICAST  MTU:1492  Metric:1
      RX packets:269808 errors:0 dropped:0 overruns:0 frame:0
      TX packets:249776 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:3
      RX bytes:269452852 (256.9 MiB)  TX bytes:15987305 (15.2 MiB)

sit0      Link encap:IPv6-in-IPv4
      inet6 addr: ::89.1.203.31/96 Диапазон:Compat
      inet6 addr: ::127.0.0.1/96 Диапазон:Unknown
      UP RUNNING NOARP  MTU:1480  Metric:1
      RX packets:0 errors:0 dropped:0 overruns:0 frame:0
      TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:0
      RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

sit1      Link encap:IPv6-in-IPv4
      inet6 addr: 2001:618:400::591:cb1f/128 Диапазон:Общий
      inet6 addr: fe80::5901:cb1f/64 Диапазон:Link
      UP POINTOPOINT RUNNING NOARP  MTU:1472  Metric:1
      RX packets:0 errors:0 dropped:0 overruns:0 frame:0
      TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:0
      RX bytes:0 (0.0 b)  TX bytes:588 (588.0 b)

any ideas how to solve that problem?

i tryed editing the script and changing all eth1 to eth0 because in ifconfig i dont see any eth1 connection but i got error too

Code:

snake@delta:~$ sudo sh LinuxScript.sh
SIOCSIFADDR: File exists
IPv6 configuration failed!

thanks.