+- Linux-Noob Forums (https://www.linux-noob.com/forums)
+-- Forum: Distro Noob (https://www.linux-noob.com/forums/forum-10.html)
+--- Forum: CentOS (https://www.linux-noob.com/forums/forum-101.html)
+--- Thread: 5.7 -i386 won't work after update (/thread-295.html)
5.7 -i386 won't work after update - borgweare - 2011-10-25
Hi there,
In case you can’t tell I’m new to Linux.
I am trying to setup my own web server with Kloxo
(A cpanel alternative).
I installed Cent OS 5.7-i386 server, and ran the GUI
(startx) and all went well.
But when I ran the updates and restarted the PC and go to
Start the GUI I just get a blank screen. [img]<___base_url___>//public/style_emoticons/default/wacko.png[/img]
I have done some reading on all the forums out there, but far
I have had no luck.
Can still use the Command Prompt (if you call it that in the Linux’s
World?) But would like to use the GUI. (Bit like using DOS instead of windows
And I’m over those days lol). [img]<___base_url___>//public/style_emoticons/default/tongue.png[/img]
The hardware I am using to test this on is
Dell Optiplex 745 2.0GHz core 2 duo
1 GB Ram
40 GB hard drive
DVD Rom
Intel Graphics Media Accelerator 3000
Thanks to all. :)
5.7 -i386 won't work after update - Dungeon-Dave - 2011-10-26
It sounds like the update may have brought down a new module (driver) for your graphics card, which is breaking Xorg.
A good place to look is: /var/log/X.org.log - try checking the last few entries in there to see what errors they show.
If you use "startx" and get no display but can still use CTRL+ALT+F1...F9 and switch back to a text console then that implies your xorg.conf has been overwritten by one with settings incompatible with your monitor. In that case, look for an xorg.conf.backup in the /etc/X11 directory - if you move your xorg.conf out of the way and copy the backup version into place, you may be able to start your GUI with the older settings.
5.7 -i386 won't work after update - borgweare - 2011-10-26
Thanks will have a look at the log,
I have try the CTRL+ALT+F1...F9 but screen just stays blank.
But I will have a look before I try starting the GUI.
Thanks for your help, will let you know how I get on.
5.7 -i386 won't work after update - borgweare - 2011-10-26
Thanks will have a look at the log,
I have try the CTRL+ALT+F1...F9 but screen just stays blank.
But I will have a look before I try starting the GUI.
Thanks for your help, will let you know how I get on.
5.7 -i386 won't work after update - borgweare - 2011-10-27
Thanks all fixed
5.7 -i386 won't work after update - Dungeon-Dave - 2011-10-27
okay.. so spill the beans - what did you do?
5.7 -i386 won't work after update - borgweare - 2011-10-27
Just rolled back to before I updated.
I tried your way of using the text console, but my commands knowledge is
of linux is not great.[img]<___base_url___>//public/style_emoticons/default/wacko.png[/img]
So I found just when you first boot the computer up Cent OS gives you about
Three seconds to enter a menu where you can roll back.[img]<___base_url___>//public/style_emoticons/default/huh.png[/img]
Thanks again for your help.:)
By the way are there any good books you would recommed on Cent OS and Linux's commands.
Thanks.